diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/inspircd.conf.example | 31 |
1 files changed, 29 insertions, 2 deletions
diff --git a/docs/inspircd.conf.example b/docs/inspircd.conf.example index 1e49fae93..34852bf4a 100644 --- a/docs/inspircd.conf.example +++ b/docs/inspircd.conf.example @@ -108,6 +108,12 @@ # <bind address="ip or host" port="port" type="clients"> # # <bind address="ip or host" port="port" type="servers"> # # # +# If InspIRCd is built for IPV6, and you wish to accept IPV4 clients, # +# then you must specify your IPV6 clients in the following form: # +# ::ffff:1.2.3.4, where 1.2.3.4 is the IPV4 address to bind the # +# port on. If InspIRCd is built for IPV4 connections (this is the # +# default) then you do not need to prefix your addresses like this. # +# # <bind address="" port="6660" type="clients"> <bind address="" port="7000" type="servers"> @@ -214,6 +220,7 @@ <connect allow="*" timeout="60" flood="10" threshold="60" pingfreq="120" sendq="262144" recvq="4096" localmax="3" globalmax="3"> <connect deny="69.254.*"> +<connect deny="3ffe:*"> #-#-#-#-#-#-#-#-#-#-#-#- CLASS CONFIGURATION -#-#-#-#-#-#-#-#-#-#-#- @@ -354,6 +361,12 @@ # that server to operoverride modes. This should only be used for # # services and protected oper servers! # # # +# NOTE: If you have built InspIRCd with IPV6 support, and you want # +# to link to an IPV4 server, you must specify the IP address in the # +# form '::ffff:1.2.3.4' where 1.2.3.4 is the IP address of the target # +# server. If you have built InspIRCd for IPV4 (this is the default) # +# you should not prefix your IP addresses in this fashion. # +# # # ____ _ _____ _ _ ____ _ _ _ # # | _ \ ___ __ _ __| | |_ _| |__ (_)___ | __ )(_) |_| | # # | |_) / _ \/ _` |/ _` | | | | '_ \| / __| | _ \| | __| | # @@ -414,9 +427,22 @@ # resolving even though the DNS server appears to be up! Most ISP and # # hosting provider DNS servers support recursive lookups. # # # +# NOTE: If you have built InspIRCd with IPV6 support, and you want # +# to use an IPV4 nameserver, you must specify the IP address in the # +# form '::ffff:1.2.3.4' where 1.2.3.4 is the IP address of the target # +# server. If you have built InspIRCd for IPV4 (this is the default) # +# you should not prefix your IP addresses in this fashion. # +# # +# IF YOUR RESOLV.CONF CONTAINS ONLY IPV4 ADDRESSES, AND YOU ARE USING # +# IPV6, YOU MUST DEFINE THE <DNS SERVER> TAG, AND USE THE ::FFFF # +# PREFIX NOTATION. IF YOU DO NOT, HOSTS WILL *NOT* RESOLVE. # +# # <dns server="127.0.0.1" timeout="5"> +# An example of using IPV4 nameservers over IPV6 +#<dns server="::ffff:127.0.0.1" timeout="5"> + #-#-#-#-#-#-#-#-#-#-#-#-#-#-# PID FILE -#-#-#-#-#-#-#-#-#-#-#-#-#-#-# # # # Define the path to the PID file here. The PID file can be used to # @@ -449,8 +475,8 @@ # 'registered' (e.g. after the initial USER/NICK/PASS on connection) # # so for example disabling NICK will not cripple your network. # # # -# <disabled commands="TOPIC MODE"> # -# # + +#<disabled commands="TOPIC MODE"> #-#-#-#-#-#-#-#-#-#-#-#-#-#-#- RTFM LINE -#-#-#-#-#-#-#-#-#-#-#-#-#-# @@ -471,6 +497,7 @@ # loglevel - specifies what detail of messages to log in the # # log file. You may select from debug, verbose, # # default, sparse and none. # +# # # allowhalfop - allows the +h channel mode # # # # noservices - If noservices is true, yes, or 1, then the first # |