diff options
| -rw-r--r-- | docs/conf/modules.conf.example | 21 | ||||
| -rw-r--r-- | docs/conf/opers.conf.example | 3 |
2 files changed, 11 insertions, 13 deletions
diff --git a/docs/conf/modules.conf.example b/docs/conf/modules.conf.example index e7735dc35..0e7b3a29b 100644 --- a/docs/conf/modules.conf.example +++ b/docs/conf/modules.conf.example @@ -483,17 +483,16 @@ #-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-# # Cloaking module: Adds usermode +x and cloaking support. -# Relies on the module m_md5.so being loaded before m_cloaking.so in -# the configuration file. +# Relies on the module m_md5.so being loaded. # To use, you should enable m_conn_umodes and add +x as # an enabled mode. See the m_conn_umodes module for more information. #<module name="m_cloaking.so"> # #-#-#-#-#-#-#-#-#-#-#- CLOAKING CONFIGURATION -#-#-#-#-#-#-#-#-#-#-#-# # # -# If you specify the m_cloaking.so module as above, you must define # -# cloak keys, and optionally a cloak prefix as shown below. The cloak # -# keys must be shared across the network for correct cloaking. # +# To use m_cloaking, you must define a cloak key, and optionally a # +# cloak prefix as shown below. The cloak key must be shared across # +# the network for correct cloaking. # # # # There are four methods of cloaking: # # # @@ -513,10 +512,10 @@ # compat-host InspIRCd 1.2-compatible host-based cloaking # # compat-ip InspIRCd 1.2-compatible ip-always cloaking # # # -# You must specify key1, key2, key3, key4 for the compat cloaking # -# modes; the values must be less than 0x80000000 and should be picked # -# at random. Prefix is mandatory, will default to network name if not # -# specified, and will always have a "-" appended. # +# If you use a compat cloaking mode then you must specify key1, key2, # +# key3, key4; the values must be less than 0x80000000 and should be # +# picked at random. Prefix is mandatory, will default to network name # +# if not specified, and will always have a "-" appended. # #-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-# # #<cloak mode="half" @@ -602,7 +601,7 @@ # Connection throttle module. Configuration: #<module name="m_connflood.so"> # -#-#-#-#-#-#-#-#-#-#-#- CONTHROTTLE CONFIGURATION -#-#-#-#-#-#-#-#-#-#-# +#-#-#-#-#-#-#-#-#-#-#- CONNTHROTTLE CONFIGURATION -#-#-#-#-#-#-#-#-#-# # seconds, maxconns - Amount of connections per <seconds>. # # timeout - Time to wait after the throttle was activated @@ -619,7 +618,7 @@ # quitmsg="Throttled" bootwait="10"> #-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-#-# -# Custom prefixes : allows for channel prefixes to be added. +# Custom prefixes: allows for channel prefixes to be added. # This can replace m_chanprotect and m_halfop, except for services that # recognise those modules by name #<module name="m_customprefix.so"> diff --git a/docs/conf/opers.conf.example b/docs/conf/opers.conf.example index 6e82e07d9..1e5abefa5 100644 --- a/docs/conf/opers.conf.example +++ b/docs/conf/opers.conf.example @@ -25,13 +25,12 @@ # ACTIONS: # - users/mass-message: allows opers with this priv to PRIVMSG and NOTICE to a server mask (e.g. NOTICE $*) # - channels/high-join-limit: allows opers with this priv to join <channels:opers> total channels instead of <channels:users> total channels. - # - channels/set-permanent: allows opers with this priv to set +P on channels with m_permchannels. # PERMISSIONS: # - users/flood/no-throttle: allows opers with this priv to send commands without being throttled (*NOTE) # - users/flood/increased-buffers: allows opers with this priv to send and recieve data without worrying about being disconnected for exceeding limits (*NOTE) # # *NOTE: These privs are potantially dangerous, as they grant users with them the ability to hammer your server's CPU/RAM as much as they want, essentially. - privs="users/auspex channels/auspex servers/auspex users/mass-message channels/high-join-limit channels/set-permanent users/flood/no-throttle users/flood/increased-buffers" + privs="users/auspex channels/auspex servers/auspex users/mass-message channels/high-join-limit users/flood/no-throttle users/flood/increased-buffers" # usermodes: Oper-only usermodes that opers with this class can use. usermodes="*" |